Home > AK47, AK74 & AKM Parts >

THREADING TOOL- ANNULAR CUTTER FOR 1/2 x 28 BARREL THREADING

Saiga Vepr AK47 25760 1/2 x 28 Annular Cutter Kit


 
Alternative Views:


Price: $81.95

Stock Status:
IN STOCK AVAILABLE FOR PURCHASE

SKU#: CNCW-ANNULAR-CUTTER-12128


OPTIONAL Drill Shank:


Qty:  
Description
 
This tool can be used to reduce a barrel OD (outside diameter) within close proximity to the size needed for 1/2 x 28 threads (approximately 0.5"). The barrel OD can start out no larger than .875 for this to work properly.
This tool provides you with one of the most economical and practical means available for reducing the barrel OD.
Easily removes the barrel shrouds covering the Saiga rifle and reduces barrel size to be threaded.
Bit OD: 0.875"
Bit ID: 0.515"

The cutter should be ran at slow RPMs (around 200), lubricated constantly, and a pilot used to keep it centered on the barrel properly.

Barrel pilot (Shown in picture) is sold separately below. Please select the correct caliber pilot.

Carolina Shooters Supply Inc. expressly denies any liability for results that may occur from the proper, or improper, use of this tool. If you are unsure about using it, please do not order.
All Sales are final on all cutting tools.




recommended accessories for this product
THREADING DIE STOCK HANDLE FOR 1 1/2" DIE THREAD CUTTING OIL THREADING DIE-14X1LH AK47, SAIGA 7.62, 5.45, 223 THREADING TOOL - 223 PILOT for ANNULAR CUTTER
Price: $20.95
Price: $5.95
Price: $37.95
Price: $13.99
DIE STOCK HANDLE SAIGA BARREL THREADING AK47 AR15 VEPR SAIGA AK47 VEPR AR15 THREAD CUTTING OIL TAP MAGIC SAIGA AK47 7.62 THREADING DIES AND ALIGNMENT TOOL Saiga Vepr AK47 223 1/2 x 28 Inch Annular Pilot Cutter Kit #25567
THREADING TOOL - 7.62x39/308 PILOT for ANNULAR CUTTER THREADING TOOL - 5.45x39 PILOT for ANNULAR CUTTER
Price: $13.99
Price: $13.99
Saiga Vepr AK47 7.62x39 308 5/8 x 24 Inch Annular Pilot Cutter Kit #25547 Saiga Vepr AK47 5.45x39mm Pilot Kit #25547

Average Rating: Average Rating: 3.5 of 5 3.5 of 5 Total Reviews: 3 Write a review »

  0 of 0 people found the following review helpful:
 
1 of 5 12128 7/8”x1” DOC July 30, 2021
Reviewer: Rene Gonzalez from Willow Park, TX United States  
Cutter did not take enough off of the barrel for the die to smoothly cut threads onto barrel. Spend a couple of hours trying to just hand sand it to get it thin enough for the ID of the die to even start. Cutter helped a lot but since it wasn’t accurate it was a huge waste of time hand sanding. First few threads were ground off due to the die trying to thread onto the barrel OD that was too large. Would not recommend, especially not at this price.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 10/22 threading made easy June 8, 2021
Reviewer: claude hanks from , LA (lower Alabama)  
Top quality cutter (same brand as I have  used in the construction field) it did the job really better than I imagined. I am well pleased, plan on ordering one for 30 cal.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Best $65 I’ve ever spent no bull March 22, 2021
Reviewer: Fred Riffle from Norwood , OH United States  
This cutter is awesome . I used a crescent wrench to turn it while pushing in with the other hand . Effortless cutting . Clean smooth cut on a cold hammer forged barrel like butter . First time user and loved it . Seriously can’t say how much easier this made my  project go. Suck it up and get the best . So Clean a buddy swore i paid a pro to do it when I sent him the picks.

Was this review helpful to you?